##// END OF EJS Templates
HG_REPOSITORIES » LPP » INSTRUMENTATION » libuc2
RSS

Clone from http://pc-instru.lpp.polytechnique.fr:5000/libuc2

Sync
jeandet -
r96:f72c1c144c9e dev_alexis
parent child
Show More
Show file before | Show file after | Hide comments
@@ -0,0 +1,47
1 /*------------------------------------------------------------------------------
2 -- This file is a part of the libuc, microcontroler library
3 -- Copyright (C) 2014, Alexis Jeandet
4 --
5 -- This program is free software; you can redistribute it and/or modify
6 -- it under the terms of the GNU General Public License as published by
7 -- the Free Software Foundation; either version 3 of the License, or
8 -- (at your option) any later version.
9 --
10 -- This program is distributed in the hope that it will be useful,
11 -- but WITHOUT ANY WARRANTY; without even the implied warranty of
12 -- MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
13 -- GNU General Public License for more details.
14 --
15 -- You should have received a copy of the GNU General Public License
16 -- along with this program; if not, write to the Free Software
17 -- Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
18 -------------------------------------------------------------------------------
19 -- Author : Alexis Jeandet
20 -- Mail : alexis.jeandet@member.fsf.org
21 -------------------------------------------------------------------------------*/
22
23 #include <uhandle.h>
24 #define USB_LowSpeed 1
25 #define USB_FullSpeed 2
26 #define USB_HighSpeed 3
27
28 #define USB_MODE_RAW 1
29 #define USB_MODE_VCP 2
30 #define USB_MODE_HID 3
31 #define USB_MODE_MSC 4
32 #define USB_MODE_AUDIO 5
33
34 struct usbdev_str
35 {
36 UHANDLE phy;
37 int (*epread) (UHANDLE phy,char *buff,uint32_t bc,char ep);
38 int (*epwrite) (UHANDLE phy,char *buff,uint32_t bc,char ep);
39 };
40
41 typedef volatile struct usbdev_str usbDev;
42
43 extern int usbdevopen(usbDev*dev, uint32_t DATAPpin,uint32_t DATAMpin,uint32_t VBUSpin,uint32_t IDpin,int USBSpeed,int usbmode);
44
45
46
47
Show file before | Show file after | Hide comments
@@ -0,0 +1,294
1 /**
2 ******************************************************************************
3 * @file usb_conf.h
4 * @author MCD Application Team
5 * @version V1.1.0
6 * @date 19-March-2012
7 * @brief General low level driver configuration
8 ******************************************************************************
9 * @attention
10 *
11 * <h2><center>&copy; COPYRIGHT 2012 STMicroelectronics</center></h2>
12 *
13 * Licensed under MCD-ST Liberty SW License Agreement V2, (the "License");
14 * You may not use this file except in compliance with the License.
15 * You may obtain a copy of the License at:
16 *
17 * http://www.st.com/software_license_agreement_liberty_v2
18 *
19 * Unless required by applicable law or agreed to in writing, software
20 * distributed under the License is distributed on an "AS IS" BASIS,
21 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
22 * See the License for the specific language governing permissions and
23 * limitations under the License.
24 *
25 ******************************************************************************
26 */
27
28 /* Define to prevent recursive inclusion -------------------------------------*/
29 #ifndef __USB_CONF__H__
30 #define __USB_CONF__H__
31
32 /* Includes ------------------------------------------------------------------*/
33 #include "stm32f4xx.h"
34
35 #define USE_USB_OTG_FS
36
37 //#define USE_USB_OTG_HS
38 //#define USE_ULPI_PHY
39
40 /** @addtogroup USB_OTG_DRIVER
41 * @{
42 */
43
44 /** @defgroup USB_CONF
45 * @brief USB low level driver configuration file
46 * @{
47 */
48
49 /** @defgroup USB_CONF_Exported_Defines
50 * @{
51 */
52
53 /* USB Core and PHY interface configuration.
54 Tip: To avoid modifying these defines each time you need to change the USB
55 configuration, you can declare the needed define in your toolchain
56 compiler preprocessor.
57 */
58 /****************** USB OTG FS PHY CONFIGURATION *******************************
59 * The USB OTG FS Core supports one on-chip Full Speed PHY.
60 *
61 * The USE_EMBEDDED_PHY symbol is defined in the project compiler preprocessor
62 * when FS core is used.
63 *******************************************************************************/
64 #ifndef USE_USB_OTG_FS
65 //#define USE_USB_OTG_FS
66 #endif /* USE_USB_OTG_FS */
67
68 #ifdef USE_USB_OTG_FS
69 #define USB_OTG_FS_CORE
70 #endif
71
72 /****************** USB OTG HS PHY CONFIGURATION *******************************
73 * The USB OTG HS Core supports two PHY interfaces:
74 * (i) An ULPI interface for the external High Speed PHY: the USB HS Core will
75 * operate in High speed mode
76 * (ii) An on-chip Full Speed PHY: the USB HS Core will operate in Full speed mode
77 *
78 * You can select the PHY to be used using one of these two defines:
79 * (i) USE_ULPI_PHY: if the USB OTG HS Core is to be used in High speed mode
80 * (ii) USE_EMBEDDED_PHY: if the USB OTG HS Core is to be used in Full speed mode
81 *
82 * Notes:
83 * - The USE_ULPI_PHY symbol is defined in the project compiler preprocessor as
84 * default PHY when HS core is used.
85 * - On STM322xG-EVAL and STM324xG-EVAL boards, only configuration(i) is available.
86 * Configuration (ii) need a different hardware, for more details refer to your
87 * STM32 device datasheet.
88 *******************************************************************************/
89 #ifndef USE_USB_OTG_HS
90 //#define USE_USB_OTG_HS
91 #endif /* USE_USB_OTG_HS */
92
93 #ifndef USE_ULPI_PHY
94 //#define USE_ULPI_PHY
95 #endif /* USE_ULPI_PHY */
96
97 #ifndef USE_EMBEDDED_PHY
98 //#define USE_EMBEDDED_PHY
99 #endif /* USE_EMBEDDED_PHY */
100
101 #ifdef USE_USB_OTG_HS
102 #define USB_OTG_HS_CORE
103 #endif
104
105 /*******************************************************************************
106 * FIFO Size Configuration in Device mode
107 *
108 * (i) Receive data FIFO size = RAM for setup packets +
109 * OUT endpoint control information +
110 * data OUT packets + miscellaneous
111 * Space = ONE 32-bits words
112 * --> RAM for setup packets = 10 spaces
113 * (n is the nbr of CTRL EPs the device core supports)
114 * --> OUT EP CTRL info = 1 space
115 * (one space for status information written to the FIFO along with each
116 * received packet)
117 * --> data OUT packets = (Largest Packet Size / 4) + 1 spaces
118 * (MINIMUM to receive packets)
119 * --> OR data OUT packets = at least 2*(Largest Packet Size / 4) + 1 spaces
120 * (if high-bandwidth EP is enabled or multiple isochronous EPs)
121 * --> miscellaneous = 1 space per OUT EP
122 * (one space for transfer complete status information also pushed to the
123 * FIFO with each endpoint's last packet)
124 *
125 * (ii)MINIMUM RAM space required for each IN EP Tx FIFO = MAX packet size for
126 * that particular IN EP. More space allocated in the IN EP Tx FIFO results
127 * in a better performance on the USB and can hide latencies on the AHB.
128 *
129 * (iii) TXn min size = 16 words. (n : Transmit FIFO index)
130 * (iv) When a TxFIFO is not used, the Configuration should be as follows:
131 * case 1 : n > m and Txn is not used (n,m : Transmit FIFO indexes)
132 * --> Txm can use the space allocated for Txn.
133 * case2 : n < m and Txn is not used (n,m : Transmit FIFO indexes)
134 * --> Txn should be configured with the minimum space of 16 words
135 * (v) The FIFO is used optimally when used TxFIFOs are allocated in the top
136 * of the FIFO.Ex: use EP1 and EP2 as IN instead of EP1 and EP3 as IN ones.
137 * (vi) In HS case 12 FIFO locations should be reserved for internal DMA registers
138 * so total FIFO size should be 1012 Only instead of 1024
139 *******************************************************************************/
140
141 /****************** USB OTG HS CONFIGURATION **********************************/
142 #ifdef USB_OTG_HS_CORE
143 #define RX_FIFO_HS_SIZE 512
144 #define TX0_FIFO_HS_SIZE 64
145 #define TX1_FIFO_HS_SIZE 372
146 #define TX2_FIFO_HS_SIZE 64
147 #define TX3_FIFO_HS_SIZE 0
148 #define TX4_FIFO_HS_SIZE 0
149 #define TX5_FIFO_HS_SIZE 0
150
151 // #define USB_OTG_HS_SOF_OUTPUT_ENABLED
152
153 #ifdef USE_ULPI_PHY
154 #define USB_OTG_ULPI_PHY_ENABLED
155 #endif
156 #ifdef USE_EMBEDDED_PHY
157 #define USB_OTG_EMBEDDED_PHY_ENABLED
158 /* wakeup is working only when HS core is configured in FS mode */
159 #define USB_OTG_HS_LOW_PWR_MGMT_SUPPORT
160 #endif
161 // #define USB_OTG_HS_INTERNAL_DMA_ENABLED
162 /* Be aware that enabling DMA mode will result in data being sent only by
163 multiple of 4 packet sizes. This is due to the fact that USB DMA does
164 not allow sending data from non word-aligned addresses.
165 For this specific application, it is advised to not enable this option
166 unless required. */
167 #define USB_OTG_HS_DEDICATED_EP1_ENABLED
168 #endif
169
170 /****************** USB OTG FS CONFIGURATION **********************************/
171 #ifdef USB_OTG_FS_CORE
172 #define RX_FIFO_FS_SIZE 128
173 #define TX0_FIFO_FS_SIZE 32
174 #define TX1_FIFO_FS_SIZE 128
175 #define TX2_FIFO_FS_SIZE 32
176 #define TX3_FIFO_FS_SIZE 0
177
178 // #define USB_OTG_FS_LOW_PWR_MGMT_SUPPORT
179 // #define USB_OTG_FS_SOF_OUTPUT_ENABLED
180 #endif
181
182 /****************** USB OTG MISC CONFIGURATION ********************************/
183 #define VBUS_SENSING_ENABLED
184
185 /****************** USB OTG MODE CONFIGURATION ********************************/
186 //#define USE_HOST_MODE
187 #define USE_DEVICE_MODE
188 //#define USE_OTG_MODE
189
190 #ifndef USB_OTG_FS_CORE
191 #ifndef USB_OTG_HS_CORE
192 #error "USB_OTG_HS_CORE or USB_OTG_FS_CORE should be defined"
193 #endif
194 #endif
195
196 #ifndef USE_DEVICE_MODE
197 #ifndef USE_HOST_MODE
198 #error "USE_DEVICE_MODE or USE_HOST_MODE should be defined"
199 #endif
200 #endif
201
202 #ifndef USE_USB_OTG_HS
203 #ifndef USE_USB_OTG_FS
204 #error "USE_USB_OTG_HS or USE_USB_OTG_FS should be defined"
205 #endif
206 #else //USE_USB_OTG_HS
207 #ifndef USE_ULPI_PHY
208 #ifndef USE_EMBEDDED_PHY
209 #error "USE_ULPI_PHY or USE_EMBEDDED_PHY should be defined"
210 #endif
211 #endif
212 #endif
213
214 /****************** C Compilers dependant keywords ****************************/
215 /* In HS mode and when the DMA is used, all variables and data structures dealing
216 with the DMA during the transaction process should be 4-bytes aligned */
217 #ifdef USB_OTG_HS_INTERNAL_DMA_ENABLED
218 #if defined (__GNUC__) /* GNU Compiler */
219 #define __ALIGN_END __attribute__ ((aligned (4))) __attribute__((section(".ahbram_data")))
220 #define __ALIGN_BEGIN
221 #else
222 #define __ALIGN_END
223 #if defined (__CC_ARM) /* ARM Compiler */
224 #define __ALIGN_BEGIN __align(4)
225 #elif defined (__ICCARM__) /* IAR Compiler */
226 #define __ALIGN_BEGIN
227 #elif defined (__TASKING__) /* TASKING Compiler */
228 #define __ALIGN_BEGIN __align(4)
229 #endif /* __CC_ARM */
230 #endif /* __GNUC__ */
231 #else
232 #define __ALIGN_BEGIN
233 #define __ALIGN_END __attribute__((section(".ahbram_data")))
234 #endif /* USB_OTG_HS_INTERNAL_DMA_ENABLED */
235
236 /* __packed keyword used to decrease the data type alignment to 1-byte */
237 #if defined (__CC_ARM) /* ARM Compiler */
238 #define __packed __packed
239 #elif defined (__ICCARM__) /* IAR Compiler */
240 #define __packed __packed
241 #elif defined ( __GNUC__ ) /* GNU Compiler */
242 #define __packed __attribute__ ((__packed__))
243 #elif defined (__TASKING__) /* TASKING Compiler */
244 #define __packed __unaligned
245 #endif /* __CC_ARM */
246
247 /**
248 * @}
249 */
250
251
252 /** @defgroup USB_CONF_Exported_Types
253 * @{
254 */
255 /**
256 * @}
257 */
258
259
260 /** @defgroup USB_CONF_Exported_Macros
261 * @{
262 */
263 /**
264 * @}
265 */
266
267 /** @defgroup USB_CONF_Exported_Variables
268 * @{
269 */
270 /**
271 * @}
272 */
273
274 /** @defgroup USB_CONF_Exported_FunctionsPrototype
275 * @{
276 */
277 /**
278 * @}
279 */
280
281
282 #endif //__USB_CONF__H__
283
284
285 /**
286 * @}
287 */
288
289 /**
290 * @}
291 */
292
293 /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
294
Show file before | Show file after | Hide comments
@@ -0,0 +1,11
1 TEMPLATE = lib
2 CONFIG += libuc2lib
3
4 SOURCES += \
5 usbdev.c
6
7 UCMODEL=stm32f4
8
9 HEADERS += \
10 ../../../include/USB/usbdev.h
11
Show file before | Show file after | Hide comments
@@ -0,0 +1,64
1 /*------------------------------------------------------------------------------
2 -- This file is a part of the libuc, microcontroler library
3 -- Copyright (C) 2014, Alexis Jeandet
4 --
5 -- This program is free software; you can redistribute it and/or modify
6 -- it under the terms of the GNU General Public License as published by
7 -- the Free Software Foundation; either version 3 of the License, or
8 -- (at your option) any later version.
9 --
10 -- This program is distributed in the hope that it will be useful,
11 -- but WITHOUT ANY WARRANTY; without even the implied warranty of
12 -- MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
13 -- GNU General Public License for more details.
14 --
15 -- You should have received a copy of the GNU General Public License
16 -- along with this program; if not, write to the Free Software
17 -- Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
18 -------------------------------------------------------------------------------
19 -- Author : Alexis Jeandet
20 -- Mail : alexis.jeandet@member.fsf.org
21 -------------------------------------------------------------------------------*/
22
23 #include <usbdev.h>
24 #include <gpio.h>
25 #include <stm32f4xx_gpio.h>
26 #include <core.h>
27 #include <stm32f4xx_rcc.h>
28 //#include <usb_core.h>
29
30 int usbfsopen(uint32_t DATAPpin,uint32_t DATAMpin,uint32_t VBUSpin,uint32_t IDpin)
31 {
32
33 RCC_APB2PeriphClockCmd(RCC_APB2Periph_SYSCFG, ENABLE);
34 gpio_t DP,DM,VBUS,ID;
35 DP = gpioopen(DATAPpin);
36 DM = gpioopen(DATAMpin);
37 VBUS = gpioopen(VBUSpin);
38 ID = gpioopen(IDpin);
39 DP |= gpiohighspeed | gpioaf | gpiopushpulltype | gpionopulltype;
40 DM |= gpiohighspeed | gpioaf | gpiopushpulltype | gpionopulltype;
41 VBUS |= gpiohighspeed | gpioindir | gpioopendraintype | gpionopulltype;
42 ID |= gpiohighspeed | gpioaf | gpiopushpulltype | gpionopulltype;
43 gpiosetconfig(&DP);
44 gpiosetconfig(&DM);
45 gpiosetconfig(&ID);
46 gpiosetconfig(&VBUS);
47
48 GPIO_PinAFConfig(GPIOGETPORT(DP), (uint8_t)(DP & 0xF), GPIO_AF_OTG1_FS);
49 GPIO_PinAFConfig(GPIOGETPORT(DM), (uint8_t)(DM & 0xF), GPIO_AF_OTG1_FS);
50 GPIO_PinAFConfig(GPIOGETPORT(ID), (uint8_t)(ID & 0xF), GPIO_AF_OTG1_FS);
51
52 RCC_AHB2PeriphClockCmd(RCC_AHB2Periph_OTG_FS, ENABLE) ;
53
54 return 0;
55 }
56
57 int usbdevopen(usbDev*dev, uint32_t DATAPpin,uint32_t DATAMpin,uint32_t VBUSpin,uint32_t IDpin,int USBSpeed,int usbmode)
58 {
59 if(USBSpeed==USB_FullSpeed)
60 {
61 return usbfsopen(PA12,PA11,PA9,PA10); //fixed pins on STM32F4
62 }
63 return -1;
64 }
Show file before | Show file after | Hide comments
@@ -1,24 +1,28
1 # use glob syntax.
1 # use glob syntax.
2 syntax: glob
2 syntax: glob
3
3
4 *.*~
4 *.*~
5 *~
5 *~
6 *.o
6 *.o
7 *.a
7 *.a
8 *.hex
8 *.hex
9 *.bin
9 *.bin
10 *.d
10 *.d
11 *.dump
11 *.dump
12 *.map
12 *.map
13 *.user
13 *.user
14 *.user.*
14 *.user.*
15 *.orig
15 *.orig
16 Makefile.*
16 Makefile.*
17 *.Makefile.*
17 *.Makefile.*
18 *.aux
18 *.aux
19 *.ps
19 *.ps
20 *.out
20 *.out
21 *.prl
21 *.prl
22 *.dfu
22 *.dfu
23 mkspecs/default/qmake.conf
23 mkspecs/default/qmake.conf
24 mkspecs/default/qplatformdefs.h
24 mkspecs/default/qplatformdefs.h
25 Makefile
26 doc/doxygen/html/*
27 doc/doxygen/latex/*
28 *.qch
General Comments 0
You need to be logged in to leave comments. Login now